Almeria Heating

Keep You House Warm This Winter With Our Heating Tips

Tag water heater repair

Water Heater Parts and Accessories

Water Heater Denver is an essential appliance that warms up your cold water so you can shower, wash dishes, and clean clothes. They’re usually electric but can also be gas or solar.

Water Heater

The conventional tank-type water heater has a large insulated storage tank and a heating element. It also has a dip tube and shut-off valve.

Thermostats are an important part of your water heater and are responsible for monitoring and regulating the temperature of the water within the tank. They work in conjunction with a control mechanism to activate or deactivate the heating elements in order to maintain your pre-set water temperature. The thermostats are also responsible for activating the dip tube to allow hot water to flow from the heater into your home’s plumbing system.

When a thermostat fails you will likely notice lukewarm or inconsistently hot water flowing from your faucets. This is because the upper thermostat signals the lower heating element to activate and heat up the top 1/3 of the water in the tank, but if the upper thermostat fails it won’t send this signal to the lower element. This can result in either the top 1/3 of the water being lukewarm or the entire tank being too hot, depending on the problem.

Water heaters that use an electronic control thermostat instead of the traditional bulb and rod thermostat use a component called a thermistor. The thermistor has an electrical resistance that varies according to the temperature. A multimeter can be used to test the thermistor for continuity and to see how much current is flowing through it. If you suspect that your thermistor has failed, a professional will be needed to replace it.

A common cause of a failed upper thermostat is when your water heater keeps tripping its high limit switch. This occurs when the upper thermostat is malfunctioning and keeping your water temperature too high which triggers the high limit switch to trip.

This is often caused by a loose electrical connection in the circuit board, but can be difficult to determine without testing with a multimeter. To test a newer electronic thermostat, shut off power to your water heater at the breaker panel, remove the access cover and insulation, and then touch one of the multimeter’s probes to grounded metal (such as the unpainted steel of the tank) and the other to each of the thermostat terminals and both of the heating element terminals. If the meter display shows continuity or zero ohms, then the thermistor is defective and needs to be replaced.

Dip Tube

Nothing keeps your home clean, sanitary, and functional like a steady supply of hot water. Whether you’re taking a shower, washing clothes, or cooking dinner, fresh hot water is critical for all your daily activities. When your hot water heater breaks down, you need to find out what caused it so that you can fix the problem and restore your supply of hot water. One common cause of insufficient hot water is a broken dip tube.

A dip tube is a short piece of pipe that connects your water heater’s cold water inlet to the bottom of its interior. The tube suppresses the 8 inches of cold water that enters the tank during use by pushing it to the bottom where a burner heats it and rises to the top for consumption. The dip tube is designed to keep a constant supply of hot water flowing through your system, but it can crack or break down over time, leaving your house with lukewarm water until the dip tube can be replaced.

Most modern water heaters use a non-metallic plastic dip tube to avoid accelerating the rusting of the steel tank and they have a better record of durability than their older, metallic predecessors. However, even these durable tubes can break down over time. When this happens, you may see small bits of plastic in your faucet aerators, shower nozzles, and washing machine inlet tubes. The dip tube can also break loose at its point of attachment to the inlet port and float freely inside your water heater. The pieces that float will collect at the unported apex of your water heater’s domed top and become available for being drawn into the inlet port at random times.

When your water heater’s dip tube becomes defective, it can be easily replaced with a new one from a plumbing supply store. Start by shutting off the power to your water heater at its circuit breaker, draining the tank, and opening the water valve to allow it to refill. Then, remove the old dip tube by removing its pipe nipple and connector from the inlet port with a flat screwdriver. Once the replacement is in place, reconnect the inlet port, restore the power to your water heater, and drain again to flush away any plastic flecks left behind.

Heater Element

Heating elements are vital to a wide range of applications and appliances. These are typically metal rods that are either straight or spiral-shaped, surrounded by a protective sheath that is capable of resisting heat to an extent. They are powered by electricity to generate the desired temperature. They are used in appliances such as medical or industrial equipment, heating systems and water heaters. In most cases, the heater element is a core component that must be properly paired with the specific application to ensure proper operation and safety. Various accessories are available to complement and enhance the functionality of heater elements. These accessories include wire and element holders, thermal switches and manual connecting clips. These devices are primarily intended to help protect the device against overheating, potentially preventing fires, product damage or serious accidents from taking place.

Heating element accessories are also useful in maintaining the longevity and functionality of the unit. This is especially important in industrial settings, where the equipment is often subject to a high level of vibration or movement. In many cases, the use of these accessories can reduce the need for repairs and replacements, saving valuable time and resources.

The most critical component of any electric water heater is the heater element. This piece of hardware is responsible for transforming electrical energy into heat in an electric water heater. This is a crucial process, and a faulty heater element can cause significant problems with the unit.

For homeowners, a faulty heater element can lead to a lack of hot water in the home or even a tripped circuit breaker. To avoid such issues, it is advisable to perform regular maintenance on the water heater, including flushing the system periodically to remove sediment buildup. Aside from this, it is also a good idea to install a water softener if you live in an area with hard water.

The replacement of the heater element in a water heater is a fairly straightforward procedure. However, it should be noted that the job involves working with high-voltage electricity and should only be attempted by those who are comfortable handling such tasks. To begin with, the power should be turned off to the unit. After this, the panels secured with screws on the side of the tank should be removed. Then, using a non-contact voltage detector, the element should be disconnected from the terminals on the front.

Tank

Tank water heaters are the most common type of hot-water heater found in North American homes. These conventional units use an insulated tank to heat and store hot water until it’s needed. They are available in sizes ranging from 30 to 80 gallons. They can be powered by electricity, natural gas or heating oil. They feature a thermostat that keeps the temperature of the water at a safe level and a safety valve that opens when pressure or temperature exceeds preset levels.

The cold-water pipe from your house’s main line enters the tank through the dip tube and is heated by the heating mechanism at the bottom of the tank. As the water heats, it rises to the top of the tank. When you turn on a hot-water faucet, the hottest water in the tank flows out through the hot water supply pipe at the top of the unit.

Most tank-type water heaters have a drain valve at the bottom of the unit, which is used to drain away sediment that builds up inside the tank. They also have a shut-off valve on the outside, to stop water flow to and from the tank.

Some tanks have a venting system to draw air in and out of the tank, helping the water heater operate more efficiently. Others have an anode rod that’s made of metal to protect the steel lining of the tank from corrosion.

While tank-type water heaters are popular and widely available, they have some drawbacks. They consume energy (gas or electricity) day and night, even when nobody’s using hot water, a process known as standby heat loss. They also have a limited capacity and may struggle to meet peak demand.

A newer alternative is the tankless water heater. These devices don’t have a storage tank, instead they heat the water as it flows through them, which saves energy. They can also be less expensive to install than traditional models. However, they still require some initial investment. A gas tankless water heater can cost up to $1,500, while an electric model costs about the same.

Water Heater Repair Tips

Licensed plumbers can repair various problems with your water heater, such as leaks, lack of hot water, or rusty water. However, depending on the type of damage or your water heater’s age, it may be more cost-efficient to replace it. For more information, contact Water Heater Repair Tampa today!

To find out how old your water heater is, consult the paperwork that came with it or check the plate on its side for the model number and serial number.

  1. Water Heater Leaks

Water heater leaks are dangerous because they lead to flooding, damage, and mold growth. These extreme damages are costly and can ruin your home’s floors, walls, and possessions. Knowing where a water heater leaks helps homeowners react quickly and save money. Homeowners should know where water heater leaks are coming from and why so they can call a plumber immediately.

Leaks originating in the drain valve area can be easy for homeowners to fix. Check the drain valve to see if it is loose or damaged. If it is, tightening it with a pipe wrench can help solve the problem. Alternatively, the drain valve may need to be replaced. However, this is an expensive repair, and you should have a professional handle it.

On the other hand, if you find puddles or pools of water around your hot water tank, it may be more complicated to diagnose and fix. These puddles could be caused by soggy drywall or spots on the ceilings that are close to where the water tank is located. You should also check the pipes connected to your water heater to see if they are loose or damaged. If you have copper water supply tubes, look for loose or cracked fittings (professionals call these dielectric nipples).

Water leaks from the top of the water heater can also indicate that it is time to replace the unit. This is because the insulative material that covers the tank can develop cracks over time. However, it is also possible that the leaks are due to high water pressure or thermal expansion. Replacing the pressure-reducing valve or replacing the anode rod often solves these issues.

The bottom of the water heater is another common place where leaks originate. This is because the sediment in your water can build up and corrode the inner lining of your hot water tank. Unfortunately, these cracks are not repairable, and you must replace the entire water heater. However, if the cracks are small, you can repair them with some patching materials.

  1. Water Heater Not Heating Up

If your water heater is not heating up, you could have several problems. Some problems may be easily fixed, but others require professional attention. Check the power supply, thermostat settings, and pilot light.

If you suspect the problem is an electrical one, first make sure the unit has electricity by checking the voltage at the top two screws on the upper thermostat and comparing that reading to what’s listed on the data plate (usually 240 volts AC). If it doesn’t, the wiring on your water heater is likely incorrect and should be replaced. This job is best left to an experienced electrician or other qualified person.

Gas-powered water heaters with pilot lights can also experience a problem with the pilot light going out. If you need to familiarize yourself with relighting the pilot light, consult your owner’s manual for instructions. Older gas water heaters with standing pilot lights sometimes have warning lights on when the light goes out. Newer units typically have a button you can press to reset the pilot light.

When the water heater’s light is flickering, it can indicate a problem with your thermocouple. This small probe is designed to sit in the pilot light’s flame and stop the gas flow if the light goes out. The probe tip can become knocked off or covered with buildup that prevents it from working properly. To fix this, relight the pilot light and adjust the thermocouple if needed.

A solid red status light on your water heater can indicate several issues, including that the tank is not filling, a leak in the pressure relief valve or temperature-pressure relief valve, the thermocouple is bad, or a gas leak. These serious problems should be addressed and require professional attention from a trained technician.

  1. Water Heater Not Producing Hot Water

You should check a few things if your water heater isn’t producing hot water. First, make sure that electricity is getting to the unit. If it isn’t, turn off the breaker and reset it. If the breaker keeps tripping, you may have an issue with your home’s electrical wiring. In this case, a qualified electrician should look at the wiring to determine what is causing it to trip.

If you use gas to heat your water, a lack of hot water could mean the pilot light has gone out. Several issues, such as air in the gas line, a closed gas valve, or a faulty thermocouple, can cause this. It is important to note that a gas water heater with a defective thermocouple can lead to carbon monoxide poisoning in your home, which is an extremely dangerous situation. Call a plumbing professional if you cannot relight the pilot light or won’t stay lit.

Another possibility is that your upper thermostat has gone out. This safety device prevents the water from exceeding 180 degrees Fahrenheit. You can test this by looking at the unit and finding the top two screws on the upper thermostat. Using a multimeter, you can test to see if there is continuity between these screws and the data plate. If there isn’t, the upper thermostat needs to be replaced by a qualified technician.

Finally, if the gas valve on the water heater is open and you can relight the pilot light, the problem may lie in the thermocouple. This small probe should be sitting directly in the pilot flame, and it can sometimes get knocked off or obstructed from working properly. You can re-position or clean the thermocouple, but you should call a plumber if it still doesn’t work. It’s also worth noting that a newer thermocouple can be purchased for around $20, and you can install it yourself. Follow the video instructions in this link for a step-by-step guide.

  1. Water Heater Not Producing Hot Water

If the water heater produces lukewarm or cold water, but you’re getting hot water from other sources in your home, this may be a sign that the dip tube is broken. The dip tube is designed to shoot incoming cold water into the bottom of your water heater tank, where it can be heated quickly and efficiently. A broken dip tube can leave cold water at the top of the tank, flowing into your plumbing before being adequately heated.

A faulty heating element or thermostat could also cause a lack of hot water from your electric water heater. If you suspect either is the problem, try adjusting their temperature settings. You can also check the voltage at the top two screws of the upper thermostat, which should match the requirements on the data plate (usually 240 volts). If the power is out to your water heater, reset the circuit breaker or fuse by flipping it to OFF and back to ON. If you are still having trouble, contact an electrician to diagnose the problem.

Another reason for a lack of hot water from your gas water heater is that the pilot light might be out. If this is the case, you’ll need to follow the instructions on the unit or detailed here for relighting the pilot light.

Some older models of gas water heaters still have a pilot light, but many newer units use glow plugs or spark ignitors instead. You must replace the entire unit if your gas water heater has neither.

If you notice any strange smells coming from your plumbing, this is probably a sign of a gas leak. This is a serious safety hazard; you should shut your gas line off before trying any repairs. If you decide to attempt the repair, ensure you have all of the right tools and knowledge, and use a professional service person for anything you cannot handle with household tools.

DIY Plumbing – Common Mistakes Homeowners Make

Plumber The Woodlands carries clean and waste water out, making it an essential part of every home. While some DIY plumbing tasks are easy for homeowners, others require specialized tools and skills.

Doing DIY plumbing without a firm understanding of the process can lead to costly repairs and damage to your house. Here are some common mistakes to avoid when performing DIY plumbing:

plumbing

Many people believe that with a little bit of elbow grease and the right tools, there’s no home repair project too big for them to tackle. This DIY spirit can be great for some things, but when it comes to plumbing repairs, even small mistakes can lead to expensive damage down the road.

One of the biggest mistakes that DIYers make when they perform plumbing projects is using the wrong tools. For example, using a pair of regular pliers instead of a set of internal pipe wrenches can lead to damaged pipes and fittings that may need to be replaced. This mistake can also be dangerous as it could result in serious injuries.

Moreover, using the wrong materials is another common mistake that DIYers make when they’re working on their plumbing projects. For instance, using PVC glue in place of proper pipe adhesive can cause leaks and other problems that will cost you money in the long run. Similarly, using shears or cutters where a hacksaw should be used can be problematic as well.

As a general rule, it’s a good idea to keep an emergency kit of the necessary tools and replacement parts in your home so you can take care of plumbing emergencies as they arise. However, you should always be aware of your limits and call a professional if a job seems too big for you to handle.

Local plumbing codes are in place to ensure that your home’s water systems work properly and safely. They govern everything from how pipes are installed to what materials are allowed. Generally, it’s illegal to perform any kind of work on your home’s plumbing system without complying with these laws. Failure to do so may result in fines or even legal action. But more importantly, it can also compromise the safety and integrity of your home’s plumbing system.

The purpose of local plumbing codes is to guarantee the safe and correct operation of your home’s water systems. They regulate everything, including the installation of pipes and the materials that are permitted. In general, breaking these laws makes it unlawful to work on your home’s plumbing system in any way. Failing to comply with this could lead to fines or even legal action. More significantly, though, it may jeopardize the integrity and safety of the plumbing system in your house.

One of the most common plumbing code violations is using non-code approved materials. For instance, if you’re replacing a faucet, it’s important to use copper or PVC fittings rather than rubber ones. Rubber ones don’t hold up well to the temperature changes in plumbing systems and may leak or break easily. Similarly, using the wrong size pipe for your new fixtures can cause them to leak or burst, leading to costly repairs.

Another reason to pay attention to plumbing codes is that many DIY plumbing projects require a permit. If you’re unsure whether or not your project requires a permit, it’s best to consult with a professional plumber. This will help you avoid committing any serious errors that could lead to fines or structural damage to your home.

Lastly, plumbing codes often address public health concerns. For example, if you’re working on a plumbing system that’s connected to your neighborhood water supply, local plumbing codes will likely prohibit you from connecting your waste pipes to these lines. This prevents cross-contamination and keeps your water safe for everyone in your community.

If you’re planning on doing a large-scale plumbing renovation, consider hiring a licensed plumber. They’ll know what building and plumbing codes to follow, which will help protect you from future plumbing problems and keep your home up to code when it comes time to sell.

There are some tasks that you can do yourself, like replacing a faucet washer or unclogging a drain. However, if you’re doing anything major, such as re-piping your entire house or installing a water heater, leave it to the professionals. Not only will this save you money in the long run, but it will also ensure that your plumbing system is up to code and meets all applicable safety standards.

Homeowners often perform DIY plumbing projects to save money or make minor repairs. However, these DIY projects can lead to bigger problems if not done correctly. This can include water damage, costly repairs, and safety hazards. In this video, Dean’s Home Services shows some of the most common DIY plumbing mistakes that beginners make.

One of the biggest mistakes is using the wrong materials when working on a plumbing project. For example, using PVC glue instead of the proper pipe adhesive can cause leaks and other problems that will cost you more in the long run. Additionally, using the incorrect size of pipes can also lead to problems.

Another mistake is over-tightening pipe fittings. This can strip the threads and break the rubber or plastic seal in the pipe connectors. Using Teflon tape or pipe dope on threaded connections can help prevent this problem.

Finally, forgetting to turn off the main water supply is a big mistake that can lead to serious water damage. Always remember to locate and turn off the main water valve before beginning any plumbing project.

Plumbing is a complex task that involves a wide range of skills. Although it is tempting to DIY plumbing projects, relying on YouTube tutorials may lead to mistakes that can cost you money and cause damage to your home. This is why it is crucial to use these guides with caution and critical thinking. Always verify the credibility of the content creators and cross-reference information to ensure accuracy.

Many homeowners are turning to YouTube to get help with their plumbing issues. The platform offers a variety of advantages, including visual guidance, a wide range of topics, and diverse content creators. YouTube also fosters a community where users can interact with each other and learn from each other’s experiences. This provides a sense of support that can empower individuals to tackle difficult plumbing tasks that were once considered exclusive to professionals.

Another advantage of YouTube is that it offers a variety of videos that can cover any topic. When searching for a particular task, you can find multiple tutorials that provide detailed step-by-step instructions. This allows you to compare different approaches and techniques and choose the one that best suits your needs. It is also important to pay attention to the comments and questions sections, which can provide valuable insights and troubleshooting tips.

Finally, the ability to watch video tutorials on a mobile device provides flexibility and convenience. This can be beneficial when dealing with emergency situations or when you have limited time. Moreover, the flexibility offered by these tutorials can help you avoid costly plumber services.

It is also important to keep in mind that not all YouTube tutorials are created equal. Some videos contain inaccurate or misleading information, which can lead to costly mistakes and injuries. Therefore, it is essential to take the time to thoroughly research any plumbing project before attempting it on your own. This includes checking out a few tutorials and practicing the technique before tackling a major plumbing issue.

YouTube is an excellent resource for DIY plumbing. However, it is vital to remember that a professional plumber can handle complex plumbing problems that cannot be addressed by online resources. Always consider your own level of skill and expertise, the specific requirements of the job, and local regulations when making decisions about DIY plumbing.

Hot Water Heater Replacement – How to Find Out If Your Water Heater Is Rusty

If you have rusty water, it could mean that sediment is building up in the tank. Draining several buckets of water and flushing the hoses can help, but if you’re still getting rusty water, it’s time to consider replacing your heater.

Hot Water Heater

Rumbling noises from the heater are another sign that it’s time to replace it. These are caused by sediment hardening and banging against the bottom of the tank. Visit https://www.hotwaternowco.com/ for more information.

If your water heater isn’t producing hot water, a broken element may be to blame. However, diagnosing the problem can be difficult without the proper tools and knowledge. Luckily, there are some basic diagnostic tests you can do to find out if the heating element is broken or not.

The easiest way to check your heating element is to turn off power to the water heater. This is usually done by shutting off the circuit breaker that powers it. You can usually find the breaker in your home’s central breaker box, which is typically located in your garage or basement.

Once you’ve turned off the power to your water heater, wait a few hours to ensure that all of the water inside of it is cool. Then, open a faucet to test the water temperature. If the water is still warm or hot, your new element is working properly. If the water is cold or lukewarm, you probably need to replace your element.

To start, you’ll need to remove the access cover panel and insulation on your water heater tank. This will expose the heating element terminal block, which is often a rectangular piece with two screws that have electrical wires connected to it. Use a screwdriver to loosen the two screws and disconnect the wires. Next, set your multimeter to the ohms setting and connect the red probe to one of the screws on the heating element and the black probe to the other screw. A functioning heating element will register a low resistance reading on your multimeter, while a broken one will read high or not register any current at all.

Thermostat

Thermostats are a water heater’s most important part, and they play an integral role in the hot water process. If your water heater is acting up, it could be due to a defective thermostat or heating element. You can test the heating element by shutting off power to the unit, removing the appropriate access panel, moving any insulation out of the way and detaching the power wires from the elements. Then, use a multimeter to measure for continuity (the electrical path present) across the terminals. If you get a reading of 1, the element is defective and needs to be replaced.

A faulty thermostat can also cause issues, such as allowing water to get too cold before turning on or indicating an inaccurate temperature setting. Checking for continuity with the multimeter can help you determine if it’s time to replace the thermostat or reset the circuit breaker.

Using the multimeter, touch one of its leads to the upper thermostat’s reset terminal and the second lead to the left-side thermostat terminal. The meter display should indicate near zero Ohms of resistance if the thermostat has continuity. Repeat this process with the lower thermostat’s terminals to make sure they’re working as well.

If you find that the thermostats are not functioning properly, shut off power to the unit by resetting the circuit breaker and press the reset button on the high-temperature cutoff switch located above the upper thermostat. It may be a good idea to purchase replacement parts from a home improvement store. Thermostats are often interchangeable, but it’s a good idea to take the old thermostat with you when shopping for a new one to make sure you’re purchasing the same model and model number. Once the new thermostat is installed, reattach the power wires and reconnect the plastic safety panel and access door.

Anode Rod

Anode rods are made of magnesium, aluminum or zinc coated around a steel core. They connect to the top of the tank and extend into the water. Essentially, they absorb the corrosive properties of your water from the metal walls of the tank. This saves the tank from rust and corrosion which could lead to leaks. However, the anode rod will eventually erode and must be replaced. Typically, this happens after three or four years.

You can usually locate the anode rod at the nipple near your hot water outlet, or it may be on top of the tank in a separate opening. You can purchase anode rods at most hardware stores, and you might be able to find them online. They cost about $50. You can also ask your plumber to replace the anode rod.

To loosen the rod, shut off your water heater and drain several gallons of water. You should be able to see a six-sided screw head on the top of the water heater, or it may be covered with a plastic cap. Spray a little lubricant, such as WD-40, over the head to loosen it. It will likely be stuck in place by corrosion, so have a helper hold the rod while you unscrew it.

The type of anode rod that you select depends on your home’s water quality, such as its acidity and PH level. Magnesium anode rods are best for homes with soft water, while aluminum anode rods are good for homes with hard water and a high PH level. Zinc anode rods work well if you have a sulfurous odor in your home’s water. You should also check your anode rod frequently, especially if you have a water softener.

Dip Tube

If you’re dealing with a tank-style hot water heater, the dip tube is responsible for sending cool water from your home’s water supply back down to the bottom of the tank so it can be reheated by the lower element. Sometimes, this tube can wear out or spring a leak. If this happens, cold water will mix with the hot water and you’ll have less hot water to use. Fortunately, replacing this part doesn’t have to cost too much.

Another component that can wear out or spring a leak is the sacrificial anode rod, which is suspended in the water tank to help retard corrosion. Typically made of magnesium or aluminum with a steel core, these rods can last up to five years before needing replacement. Changing the anode rod should be done on a regular basis to ensure it will continue to protect the tank from erosion.

A gas water heater also has a temperature pressure relief valve, which prevents the water heater from overheating. It’s important to test this valve regularly, as it can become worn out over time. Generally, you can simply lift or lower the handle to relieve the excess pressure in the valve.

If you’re a homeowner who wants to replace their own hot water heater, the first step is removing the old one. This is a fairly heavy, cumbersome task and can be difficult for homeowners without the proper tools. It’s best to have a friend or neighbor assist you, as well as rent an appliance dolly to get the old tank down and the new one up.

Pressure Valve

The water heater’s pressure valve (or temperature and pressure relief valve) is an essential safety feature that keeps the tank from bursting. When heat and pressure levels rise too high, the valve opens through an auxiliary route (a copper or flex line that’s regionally code dependent) to escape from the top of the water heater and relieve the buildup of pressure.

The pressure valve operates based on the force acting against the valve seat, opening when upstream pressure increases beyond a pre-set limit. When the valve opens, it releases a large amount of steam or water to reduce the pressure and prevent the potential damage caused by a tank rupture.

As the steam or water exits the discharge pipe, it creates a vacuum that draws in air through the venting line connected to the valve. This air will fill the void created by the discharge line and create a balance of pressures between the tank and the water lines in the home. The venting line is then closed, the pressure equalized, and the temperature set to the proper level.

Most water heaters have a float that’s attached to the pressure valve. The float is held up by an inner mechanism with a reduced-area throat that limits the size of the flow. The inner mechanism also has a spring that’s tensioned to open the valve. A screw on the top of the pressure reducing valve allows you to increase or decrease the tension in the spring, increasing or decreasing the amount of pressure that can be relieved by the valve. Keeping the pressure regulated in this manner helps to protect your home’s water pipes and fixtures from excessive stress and strain.